Stainless Steel Cold Rolled Sheet Specification

The four grades share one specification and differ only in chemistry, so the sizes, finishes and tolerances below apply equally to all of them.

Property Details
Standard ASTM A240 / ASME SA240
Grades 202, 304, 316, 430
Thickness 0.3 mm to 6.0 mm
Width 1000 mm, 1219 mm, 1250 mm, 1500 mm; up to 2000 mm on request
Length 2000 mm, 2438 mm (8 ft), 3048 mm (10 ft), 6000 mm, or cut to length
Sheet Sizes 4 ft × 8 ft (1219 × 2438 mm), 4 ft × 10 ft (1219 × 3048 mm), custom
Forms Sheet, Coil, Strip, Slit Coil
Surface Finish 2B, BA (bright annealed), No. 4 brushed, Hairline, No. 8 mirror
Condition Cold rolled, annealed, descaled and skin passed
Edge Condition Mill Edge, Slit Edge

Stainless Steel CR Sheet Sizes and Gauges

Gauge is the number most enquiries arrive in, so the table below gives it alongside both thickness units and both weight units. Stainless is 8.00 g/cm³, which means every millimetre of thickness is 8.00 kg per square metre, and the rest of the table follows from that. The gauges below run 26 to 11, which is 0.476 mm to 3.175 mm of the 0.3 mm to 6.0 mm stocked band. Mill edge is the strip as it came off the slitter. Slit edge is trimmed to a set width, and it is the one to order when the edge will be welded or left on show.

Gauge Thickness (in) Thickness (mm) Weight (kg/m²) Weight (lb/sq ft)
26 GA 0.019 0.476 3.81 0.78
24 GA 0.025 0.635 5.08 1.04
22 GA 0.031 0.794 6.35 1.30
20 GA 0.038 0.952 7.62 1.56
18 GA 0.050 1.270 10.16 2.08
16 GA 0.062 1.588 12.70 2.60
14 GA 0.078 1.984 15.88 3.25
12 GA 0.109 2.778 22.22 4.55
11 GA 0.125 3.175 25.40 5.20

Finishes on Stainless Steel Cold Rolled Sheet

The finish is rolled and polished in at the mill rather than put on afterwards, and it is the main reason to buy cold rolled instead of hot rolled stainless sheet. 2B is the default on everything held here, and the other four are ordered by name.

FinishHow it looksWhat it is ordered for
2BSmooth and matte with a low sheenThe standard supply finish. Tanks, panels, and anything to be formed or welded
BA (bright annealed)Reflective straight off the mill, with no polishingAppliance fronts and trim that need a bright face without polishing cost
No. 4Directional satin, brushed one wayWorktops, splashbacks and lift interiors
Hairline (HL)Finer and longer brush lines than No. 4Architectural panels and door furniture
No. 8 mirrorPolished until it reflects clearlyFeature panels, signage and decorative columns

All five start from the same cold rolled, annealed and descaled strip, so the grade underneath is unchanged by the choice. What changes is the cost and the way the face behaves in service. A brushed or mirror finish shows fingerprints and fine scratches that a 2B face hides, which is why 2B stays the default on anything that will be worked rather than looked at.

Cold Rolled Stainless Steel Sheet Price

CR SS sheet is priced on the alloy in it before anything else, and nickel is the dearest part of that alloy. The bands below are the ones quoted on each grade page, converted at ₹85 to the dollar.

GradePrice in India (per kg)Export price (per kg)
SS 202 CR Sheetfrom ₹145from $1.71
SS 304 CR Sheet₹180 to ₹300$2.12 to $3.53
SS 316 CR Sheet₹260 to ₹376$3.06 to $4.42
SS 430 CR Sheet₹130 to ₹450$1.53 to $5.29

Within a grade, thickness and order size move the figure. Thin gauges cost more per kilo than heavy ones because the mill makes more passes per tonne, and a brushed or mirror face adds to both. Nickel and molybdenum are bought on the open market, which is why the 304 and 316 figures are quoted for the week rather than the year.

Get a Price on Cold Rolled Steel Sheets Request a Quote

Where SS CR Sheet Is Used

Cold rolled stainless steel sheet goes into work where the surface is part of the product. Four kinds of job account for most of what leaves here, and the grade is usually settled by the room the sheet ends up in rather than by the forming it has to take.

Food and Catering Equipment

Worktops, splashbacks, sink units and tank linings are 304 work, usually in No. 4 so that wear marks blend into the brushed grain instead of standing out against it. The face takes a hot caustic wash down without pitting, which is the test a catering kitchen applies every night.

Architectural and Interior Panels

Lift car interiors, column cladding, signage and door furniture are chosen on finish before anything else, which is why Hairline and No. 8 mirror sell into this work. 304 covers most inland jobs and 316 takes over within reach of salt air.

Appliance and White Goods Panels

Cooker fronts, extractor hoods and fridge doors are mostly 430, partly on cost and partly because it is magnetic, so door seals and mounting magnets hold against it. The duty is dry and indoors; wet or chlorinated service belongs to the austenitic grades.

Process Plant and Chloride Service Panels

Tank skins, guards and ducting in chemical, pharmaceutical and coastal plant are 316, bought for the 2.00 to 3.00% molybdenum rather than for the finish. 2B is the usual face, because the panel is there to work and not to be looked at.

Grades of Cold Rolled Stainless Steel Sheet

What separates the four is the alloy, not the rolling. All of them are cold rolled to the same tolerances and sold in the same finishes. The choice comes down to how much chromium, nickel and molybdenum the job needs, and whether the sheet is allowed to be magnetic.

Property202 CR304 CR316 CR430 CR
StructureAusteniticAusteniticAusteniticFerritic
Chromium17.0 to 19.0%17.5 to 19.5%16.0 to 18.0%16.0 to 18.0%
Nickel4.0 to 6.0%8.0 to 10.5%10.0 to 14.0%0.75% max
MolybdenumNoneNone2.00 to 3.00%None
Tensile strength, min620 MPa515 MPa515 MPa450 MPa
MagneticNo, when annealedNo, when annealedNo, when annealedYes, always

Stainless Steel 202 CR Sheet

Stainless Steel 202 is an austenitic chromium-nickel-manganese alloy that puts manganese in place of part of the nickel, which is what makes it the cheapest of the three austenitic grades. ASTM A240 sets its tensile minimum at 620 MPa, the highest here, and 202 cold rolled sheet goes into household fittings, sink units and interior trim where the air stays dry.

Stainless Steel 304 CR Sheet

Stainless Steel 304 is the grade most enquiries mean when they say stainless, and it covers general indoor, architectural and food work without argument. It carries 17.5 to 19.5% chromium and 8.0 to 10.5% nickel, welds and forms readily, and 304 cold rolled sheet is the one held in the widest range of finishes.

Stainless Steel 316 CR Sheet

Stainless Steel 316 adds 2.00 to 3.00% molybdenum, and that is the whole reason to pay the difference over 304. Molybdenum holds the passive film together where chlorides would otherwise break through it, so 316 cold rolled sheet is what goes into coastal work, chemical plant and anything washed down with chlorinated water.

Stainless Steel 430 CR Sheet

Stainless Steel 430 is ferritic rather than austenitic, so it carries almost no nickel, stays magnetic in every condition and resists oxidation to 815°C in continuous service. Its tensile minimum is 450 MPa, below the austenitic three, so it bends less far before it cracks. Appliance panels and dry indoor trim are where 430 cold rolled sheet earns its place, rather than wet or chloride service.

Shipping & Packaging

Main export packaging setup Heavy-Duty Wooden Box Packing
Export Packaging Standard

A 2B or polished face marks if anything is dragged across it, so bright and brushed sheets leave with PVC film on the show side and the film stays put until the panel is fitted. Bundles are interleaved so that no two faces rub against each other on the way.

  • Heavy-duty wooden boxes or strapped bundles, with moisture barrier lining
  • LLDPE stretch film wrapping on all bundles
  • Edge and corner protection with plastic padding
  • Silica gel desiccants to minimise moisture exposure
  • ISPM-15 compliant wooden packaging for export
Bundle Yard Staging Sheet Bundle Yard Staging
Bundle Edge Protection Sheet Bundle Edge Protection
Export-Ready Bundles Wrapped Export-Ready Bundles

We Export Worldwide

Sachiya Steel International supplies stainless steel products to major industrial markets across North America, Europe, the Middle East, Asia and Africa with export-ready documentation and logistics support.

  • USA flagUSA
  • Canada flagCanada

Frequently Asked Questions

What is cold rolled stainless steel sheet used for?+
Food and catering equipment, architectural and interior panels, appliance fronts and process plant panels take most of it. What they have in common is that the surface is seen or has to be cleaned, and that is what cold rolling buys over hot rolling.
Why does cold rolled stainless cost more than hot rolled?+
The alloy in it costs the same either way. The extra pays for the cold mill passes, the second anneal and the skin pass that puts the 2B face on. What that buys is a gauge held closer and a surface that needs no further work, so the cost sits with the mill instead of in your shop.
Which stainless CR sheet grade should I choose?+
202 is the cheapest austenitic grade and suits dry indoor fittings and trim. 304 covers general indoor, food and architectural work and is the default. 316 adds 2.00 to 3.00% molybdenum and is specified where chlorides, coastal air or chemical duty are involved. 430 is ferritic and magnetic, which suits appliance panels but rules it out of wet service.
Is cold rolled stainless sheet stronger than hot rolled?+
Not on paper. ASTM A240 gives one tensile and one yield minimum per grade, so 304 is bought to 515 MPa whichever mill route it took. Cold work does harden the metal, but sheet is supplied annealed, which takes that hardening back out before it ships.
Which standard covers SS CR sheet?+
ASTM A240 / ASME SA240 is the material standard for all four grades held here, and ASTM A480 sets the dimensional tolerances that go with it. Buyers working to European or Japanese documents will see EN 10088-2 and JIS G4305 quoted against the same material.

Contact Us for Availability and Custom Sizes Request a Quote